| BRAND |
MODEL |
ERROR CODE |
CAUSE |
| TOSHIBA |
1210 |
E1 |
Paper jammed |
| TOSHIBA |
1210 |
E2 |
Paper jam in the fuser area |
| TOSHIBA |
1210 |
E3 |
Paper jam at start-up |
| TOSHIBA |
1210 |
E5 |
Paper jam in the tray |
| TOSHIBA |
1210 |
E7 |
Paper jam in the registration area |
| TOSHIBA |
1210 |
C1 |
copy
table position error |
| TOSHIBA |
1210 |
C2 |
The
paper is not fed from the tray when the copy
table starts moving |
| TOSHIBA |
1210 |
C3 |
copy
table drive error |
| TOSHIBA |
1210 |
C4 |
copy
table position error |
| TOSHIBA |
1210 |
C5 |
Copy
table end position error |
| TOSHIBA |
1210 |
C6 |
Copy
table position error at the end of the copy
cicle |
| TOSHIBA |
1210 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
1210 |
C8 |
Thermofuse blown |
| TOSHIBA |
1210 |
CP |
Main
drive overloaded |
| TOSHIBA |
1210 |
CA |
Main
Board defective |
| TOSHIBA |
1310 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
1310 |
E1 |
Paper jam in the machine |
| TOSHIBA |
1310 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
1310 |
E3 |
Paper jam at start-up |
| TOSHIBA |
1310 |
E5 |
Paper jam in the paper tray |
| TOSHIBA |
1310 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
1310 |
C5 |
Copy
table drive overloaded |
| TOSHIBA |
1310 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
1310 |
CE |
EPROM defective or missing |
| TOSHIBA |
1310 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
1310 |
CD |
EPROM end of life |
| TOSHIBA |
1310 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
1550 |
E01 |
Paper jam in the machine |
| TOSHIBA |
1550 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
1550 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
1550 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
1550 |
E14 |
Paper jam in the Paper Feed Unit |
| TOSHIBA |
1550 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
1550 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
1550 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
1550 |
E75 |
Original jammed |
| TOSHIBA |
1550 |
E81 |
Sorter paper jam |
| TOSHIBA |
1550 |
E82 |
Sorter paper jam |
| TOSHIBA |
1550 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
1550 |
C21 |
Optical system initialization error |
| TOSHIBA |
1550 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
1550 |
C32 |
Easy
set-up error |
| TOSHIBA |
1550 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
1550 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
1550 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
1550 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
1550 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
1550 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
1550 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
1550 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
1550 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
1550 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
1550 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
1550 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
1550 |
C85 |
Home
position error in sorter |
| TOSHIBA |
1550 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
1550 |
C94 |
Optical system initialization error |
| TOSHIBA |
1560 |
E01 |
Paper jam in the machine |
| TOSHIBA |
1560 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
1560 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
1560 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
1560 |
E14 |
Paper jam in the Paper Feed Unit |
| TOSHIBA |
1560 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
1560 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
1560 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
1560 |
E75 |
Original jammed |
| TOSHIBA |
1560 |
E81 |
Sorter paper jam |
| TOSHIBA |
1560 |
E82 |
Sorter paper jam |
| TOSHIBA |
1560 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
1560 |
C21 |
Optical system initialization error |
| TOSHIBA |
1560 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
1560 |
C32 |
Easy
set-up error |
| TOSHIBA |
1560 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
1560 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
1560 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
1560 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
1560 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
1560 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
1560 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
1560 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
1560 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
1560 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
1560 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
1560 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
1560 |
C85 |
Home
position error in sorter |
| TOSHIBA |
1560 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
1560 |
C94 |
Optical system initialization error |
| TOSHIBA |
1650 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
1650 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
1650 |
E3 |
Paper jam at start-up |
| TOSHIBA |
1650 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
1650 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
1650 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
1650 |
C5 |
Optical system initialization error |
| TOSHIBA |
1650 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
1650 |
CF |
toner density error |
| TOSHIBA |
1650 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
1650 |
A4 |
Sorter problems |
| TOSHIBA |
1650 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
1650 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
1650 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
1710 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
1710 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
1710 |
E3 |
Paper jam at start-up |
| TOSHIBA |
1710 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
1710 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
1710 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
1710 |
C5 |
Optical system initialization error |
| TOSHIBA |
1710 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
1710 |
CF |
toner density error |
| TOSHIBA |
1710 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
1710 |
A4 |
Sorter problems |
| TOSHIBA |
1710 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
1710 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
1710 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2050 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
2050 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
2050 |
E3 |
Paper jam at start-up |
| TOSHIBA |
2050 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
2050 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
2050 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
2050 |
C5 |
Optical system initialization error |
| TOSHIBA |
2050 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2050 |
CF |
toner density error |
| TOSHIBA |
2050 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
2050 |
A4 |
Sorter problems |
| TOSHIBA |
2050 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
2050 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
2050 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2060 |
E01 |
Paper jam in the machine |
| TOSHIBA |
2060 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
2060 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
2060 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
2060 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
2060 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
2060 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
2060 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
2060 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
2060 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
2060 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
2060 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
2060 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
2060 |
E22 |
Paper jam during transport |
| TOSHIBA |
2060 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
2060 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
2060 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
2060 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
2060 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
2060 |
E75 |
Original jammed |
| TOSHIBA |
2060 |
E81 |
Sorter paper jam |
| TOSHIBA |
2060 |
E82 |
Sorter paper jam |
| TOSHIBA |
2060 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
2060 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
2060 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
2060 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
2060 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
2060 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
2060 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
2060 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
2060 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
2060 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
2060 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
2060 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
2060 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
2060 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
2060 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
2060 |
C21 |
Optical system initialization error |
| TOSHIBA |
2060 |
C22 |
Lens
home position error |
| TOSHIBA |
2060 |
C23 |
mirrors home position error |
| TOSHIBA |
2060 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2060 |
C32 |
Easy
set-up error |
| TOSHIBA |
2060 |
C33 |
Easy
set-up error |
| TOSHIBA |
2060 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
2060 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2060 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
2060 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
2060 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
2060 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
2060 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
2060 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
2060 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
2060 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
2060 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
2060 |
C80 |
Sorter power supply problems |
| TOSHIBA |
2060 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
2060 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
2060 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
2060 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
2060 |
C85 |
Home
position error in sorter |
| TOSHIBA |
2060 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
2060 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
2060 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
2060 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
2060 |
C94 |
Optical system initialization error |
| TOSHIBA |
2310 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
2310 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
2310 |
E3 |
Paper jam at start-up |
| TOSHIBA |
2310 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
2310 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
2310 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
2310 |
ED |
Original jam in the feeder |
| TOSHIBA |
2310 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
2310 |
C5 |
Optical system initialization error |
| TOSHIBA |
2310 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2310 |
CF |
toner density error |
| TOSHIBA |
2310 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
2310 |
A4 |
Sorter problems |
| TOSHIBA |
2310 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
2310 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
2310 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
2310 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2500 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
2500 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
2500 |
E3 |
Paper jam at start-up |
| TOSHIBA |
2500 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
2500 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
2500 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
2500 |
ED |
Original jam in the feeder |
| TOSHIBA |
2500 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
2500 |
C5 |
Optical system initialization error |
| TOSHIBA |
2500 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2500 |
CF |
toner density error |
| TOSHIBA |
2500 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
2500 |
A4 |
Sorter problems |
| TOSHIBA |
2500 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
2500 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
2500 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
2500 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2510 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
2510 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
2510 |
E3 |
Paper jam at start-up |
| TOSHIBA |
2510 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
2510 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
2510 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
2510 |
ED |
Original jam in the feeder |
| TOSHIBA |
2510 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
2510 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
2510 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
2510 |
C5 |
Optical system initialization error |
| TOSHIBA |
2510 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2510 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
2510 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
2510 |
CF |
toner density error |
| TOSHIBA |
2510 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
2510 |
A2 |
Duplex functional problems |
| TOSHIBA |
2510 |
A4 |
Sorter problems |
| TOSHIBA |
2510 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
2510 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
2510 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
2510 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2550 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
2550 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
2550 |
E3 |
Paper jam at start-up |
| TOSHIBA |
2550 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
2550 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
2550 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
2550 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
2550 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
2550 |
ED |
Original jam in the feeder |
| TOSHIBA |
2550 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
2550 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
2550 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
2550 |
C5 |
Optical system initialization error |
| TOSHIBA |
2550 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2550 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
2550 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
2550 |
CF |
toner density error |
| TOSHIBA |
2550 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
2550 |
A2 |
Duplex functional problems |
| TOSHIBA |
2550 |
A4 |
Sorter problems |
| TOSHIBA |
2550 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
2550 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
2550 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
2550 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2810 |
E1 |
Paper jam in the machine |
| TOSHIBA |
2810 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
2810 |
E3 |
Paper jam at start-up |
| TOSHIBA |
2810 |
E5 |
Paper jam in the paper tray |
| TOSHIBA |
2810 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
2810 |
E7 |
Paper jam in the feed area or registration |
| TOSHIBA |
2810 |
C1 |
Copy
table start-up position error |
| TOSHIBA |
2810 |
C2 |
The
paper does not feed when the copy table starts
moving |
| TOSHIBA |
2810 |
C3 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
2810 |
C4 |
Copy
table home position error |
| TOSHIBA |
2810 |
C5 |
Copy
table end position error |
| TOSHIBA |
2810 |
C6 |
Copy
table reverse movement error |
| TOSHIBA |
2810 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2810 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
2860 |
E01 |
Paper jam in the machine |
| TOSHIBA |
2860 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
2860 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
2860 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
2860 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
2860 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
2860 |
E11 |
Duplex entrance jam |
| TOSHIBA |
2860 |
E12 |
Paper misfeed at the manula feed table |
| TOSHIBA |
2860 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
2860 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
2860 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
2860 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
2860 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
2860 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
2860 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
2860 |
E22 |
Paper jam during transport |
| TOSHIBA |
2860 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
2860 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
2860 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
2860 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
2860 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
2860 |
E75 |
Original jammed |
| TOSHIBA |
2860 |
E81 |
Sorter paper jam |
| TOSHIBA |
2860 |
E82 |
Sorter paper jam |
| TOSHIBA |
2860 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
2860 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
2860 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
2860 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
2860 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
2860 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
2860 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
2860 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
2860 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
2860 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
2860 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
2860 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
2860 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
2860 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
2860 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
2860 |
C21 |
Optical system initialization error |
| TOSHIBA |
2860 |
C22 |
Lens
home position error |
| TOSHIBA |
2860 |
C23 |
mirrors home position error |
| TOSHIBA |
2860 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2860 |
C33 |
Easy
set-up error |
| TOSHIBA |
2860 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
2860 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2860 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
2860 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
2860 |
C45 |
problems with the sub-thrmistor |
| TOSHIBA |
2860 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
2860 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
2860 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
2860 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
2860 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
2860 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
2860 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
2860 |
C80 |
Sorter power supply problems |
| TOSHIBA |
2860 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
2860 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
2860 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
2860 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
2860 |
C85 |
Home
position error in sorter |
| TOSHIBA |
2860 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
2860 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
2860 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
2860 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
2860 |
C94 |
Optical system initialization error |
| TOSHIBA |
2870 |
E01 |
Paper jam in the machine |
| TOSHIBA |
2870 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
2870 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
2870 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
2870 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
2870 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
2870 |
E11 |
Duplex entrance jam |
| TOSHIBA |
2870 |
E12 |
Paper misfeed at the manula feed table |
| TOSHIBA |
2870 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
2870 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
2870 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
2870 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
2870 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
2870 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
2870 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
2870 |
E22 |
Paper jam during transport |
| TOSHIBA |
2870 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
2870 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
2870 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
2870 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
2870 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
2870 |
E75 |
Original jammed |
| TOSHIBA |
2870 |
E81 |
Sorter paper jam |
| TOSHIBA |
2870 |
E82 |
Sorter paper jam |
| TOSHIBA |
2870 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
2870 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
2870 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
2870 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
2870 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
2870 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
2870 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
2870 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
2870 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
2870 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
2870 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
2870 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
2870 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
2870 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
2870 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
2870 |
C21 |
Optical system initialization error |
| TOSHIBA |
2870 |
C22 |
Lens
home position error |
| TOSHIBA |
2870 |
C23 |
mirrors home position error |
| TOSHIBA |
2870 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
2870 |
C33 |
Easy
set-up error |
| TOSHIBA |
2870 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
2870 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
2870 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
2870 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
2870 |
C45 |
problems with the sub-thrmistor |
| TOSHIBA |
2870 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
2870 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
2870 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
2870 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
2870 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
2870 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
2870 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
2870 |
C80 |
Sorter power supply problems |
| TOSHIBA |
2870 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
2870 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
2870 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
2870 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
2870 |
C85 |
Home
position error in sorter |
| TOSHIBA |
2870 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
2870 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
2870 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
2870 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
2870 |
C94 |
Optical system initialization error |
| TOSHIBA |
3110 |
E1 |
Paper jam in the machine |
| TOSHIBA |
3110 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3110 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3110 |
E5 |
Paper jam in the paper tray |
| TOSHIBA |
3110 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
3110 |
E7 |
Paper jam in the feed area or registration |
| TOSHIBA |
3110 |
C1 |
Copy
table start-up position error |
| TOSHIBA |
3110 |
C2 |
The
paper does not feed when the copy table starts
moving |
| TOSHIBA |
3110 |
C3 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
3110 |
C4 |
Copy
table home position error |
| TOSHIBA |
3110 |
C5 |
Copy
table end position error |
| TOSHIBA |
3110 |
C6 |
Copy
table reverse movement error |
| TOSHIBA |
3110 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3110 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3210 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
3210 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3210 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3210 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
3210 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
3210 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
3210 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
3210 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
3210 |
ED |
Original jam in the feeder |
| TOSHIBA |
3210 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
3210 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
3210 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
3210 |
C5 |
Optical system initialization error |
| TOSHIBA |
3210 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3210 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
3210 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
3210 |
CF |
toner density error |
| TOSHIBA |
3210 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3210 |
A2 |
Duplex functional problems |
| TOSHIBA |
3210 |
A4 |
Sorter problems |
| TOSHIBA |
3210 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
3210 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
3210 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
3210 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
3220 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
3220 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3220 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3220 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
3220 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
3220 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
3220 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
3220 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
3220 |
ED |
Original jam in the feeder |
| TOSHIBA |
3220 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
3220 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
3220 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
3220 |
C5 |
Optical system initialization error |
| TOSHIBA |
3220 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3220 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
3220 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
3220 |
CF |
toner density error |
| TOSHIBA |
3220 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3220 |
A2 |
Duplex functional problems |
| TOSHIBA |
3220 |
A4 |
Sorter problems |
| TOSHIBA |
3220 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
3220 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
3220 |
A7 |
Communication problems with the feeder |
| |
|
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
3301 |
E1 |
Paper jam in the machine |
| TOSHIBA |
3301 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3301 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3301 |
E5 |
Paper jam in the paper tray |
| TOSHIBA |
3301 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
3301 |
E7 |
Paper jam in the feed area or registration |
| TOSHIBA |
3301 |
C1 |
Copy
table start-up position error |
| TOSHIBA |
3301 |
C2 |
The
paper does not feed when the copy table starts
moving |
| TOSHIBA |
3301 |
C3 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
3301 |
C4 |
Copy
table home position error |
| TOSHIBA |
3301 |
C5 |
Copy
table end position error |
| TOSHIBA |
3301 |
C6 |
Copy
table reverse movement error |
| TOSHIBA |
3301 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3301 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3550 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
3550 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3550 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3550 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
3550 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
3550 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
3550 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
3550 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
3550 |
ED |
Original jam in the feeder |
| TOSHIBA |
3550 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
3550 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
3550 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
3550 |
C5 |
Optical system initialization error |
| TOSHIBA |
3550 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3550 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
3550 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
3550 |
CF |
toner density error |
| TOSHIBA |
3550 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3550 |
A2 |
Duplex functional problems |
| TOSHIBA |
3550 |
A4 |
Sorter problems |
| TOSHIBA |
3550 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
3550 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
3550 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
3550 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
3560 |
E01 |
Paper jam in the machine |
| TOSHIBA |
3560 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
3560 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
3560 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
3560 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
3560 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
3560 |
E11 |
Duplex entrance jam |
| TOSHIBA |
3560 |
E12 |
Paper misfeed at the manula feed table |
| TOSHIBA |
3560 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
3560 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
3560 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
3560 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
3560 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
3560 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
3560 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
3560 |
E22 |
Paper jam during transport |
| TOSHIBA |
3560 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
3560 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
3560 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
3560 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
3560 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
3560 |
E75 |
Original jammed |
| TOSHIBA |
3560 |
E81 |
Sorter paper jam |
| TOSHIBA |
3560 |
E82 |
Sorter paper jam |
| TOSHIBA |
3560 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
3560 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
3560 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
3560 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
3560 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
3560 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
3560 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
3560 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
3560 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
3560 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
3560 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
3560 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
3560 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
3560 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
3560 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
3560 |
C21 |
Optical system initialization error |
| TOSHIBA |
3560 |
C22 |
Lens
home position error |
| TOSHIBA |
3560 |
C23 |
mirrors home position error |
| TOSHIBA |
3560 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
3560 |
C33 |
Easy
set-up error |
| TOSHIBA |
3560 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
3560 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3560 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
3560 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
3560 |
C45 |
problems with the sub-thrmistor |
| TOSHIBA |
3560 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
3560 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
3560 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
3560 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
3560 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
3560 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
3560 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
3560 |
C80 |
Sorter power supply problems |
| TOSHIBA |
3560 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
3560 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
3560 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
3560 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
3560 |
C85 |
Home
position error in sorter |
| TOSHIBA |
3560 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
3560 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
3560 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
3560 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
3560 |
C94 |
Optical system initialization error |
| TOSHIBA |
3570 |
E01 |
Paper jam in the machine |
| TOSHIBA |
3570 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
3570 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
3570 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
3570 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
3570 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
3570 |
E11 |
Duplex entrance jam |
| TOSHIBA |
3570 |
E12 |
Paper misfeed at the manula feed table |
| TOSHIBA |
3570 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
3570 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
3570 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
3570 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
3570 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
3570 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
3570 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
3570 |
E22 |
Paper jam during transport |
| TOSHIBA |
3570 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
3570 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
3570 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
3570 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
3570 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
3570 |
E75 |
Original jammed |
| TOSHIBA |
3570 |
E81 |
Sorter paper jam |
| TOSHIBA |
3570 |
E82 |
Sorter paper jam |
| TOSHIBA |
3570 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
3570 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
3570 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
3570 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
3570 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
3570 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
3570 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
3570 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
3570 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
3570 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
3570 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
3570 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
3570 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
3570 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
3570 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
3570 |
C21 |
Optical system initialization error |
| TOSHIBA |
3570 |
C22 |
Lens
home position error |
| TOSHIBA |
3570 |
C23 |
mirrors home position error |
| TOSHIBA |
3570 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
3570 |
C33 |
Easy
set-up error |
| TOSHIBA |
3570 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
3570 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3570 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
3570 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
3570 |
C45 |
problems with the sub-thrmistor |
| TOSHIBA |
3570 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
3570 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
3570 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
3570 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
3570 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
3570 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
3570 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
3570 |
C80 |
Sorter power supply problems |
| TOSHIBA |
3570 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
3570 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
3570 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
3570 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
3570 |
C85 |
Home
position error in sorter |
| TOSHIBA |
3570 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
3570 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
3570 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
3570 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
3570 |
C94 |
Optical system initialization error |
| TOSHIBA |
3701 |
E0 |
Paper jammed in the machine at power-up |
| TOSHIBA |
3701 |
E1 |
Paper jam in the fusing or transport area |
| TOSHIBA |
3701 |
E2 |
Paper jam in the fusing unit |
| TOSHIBA |
3701 |
E3 |
Misfeed at the manual feed table |
| TOSHIBA |
3701 |
E6 |
Copy
table drive problem |
| TOSHIBA |
3701 |
E7 |
Copy
table drive problem |
| TOSHIBA |
3701 |
E8 |
Copy
table drive problem |
| TOSHIBA |
3701 |
E9 |
Copy
table reverse clutch not working |
| TOSHIBA |
3810 |
E0 |
Used
toner bottle full |
| TOSHIBA |
3810 |
E1 |
Paper jam in the machine |
| TOSHIBA |
3810 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3810 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3810 |
E5 |
Paper jam in the paper tray |
| TOSHIBA |
3810 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
3810 |
C5 |
Copy
table end position error |
| TOSHIBA |
3810 |
C6 |
Copy
table reverse movement error |
| TOSHIBA |
3810 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3810 |
CE |
EPROM defective or missing |
| TOSHIBA |
3810 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3810 |
CD |
EPROM end of life |
| TOSHIBA |
3810 |
CF |
Development unit missing, toner density problem |
| TOSHIBA |
3910 |
E0 |
Used
toner bottle full |
| TOSHIBA |
3910 |
E1 |
Paper jam in the machine |
| TOSHIBA |
3910 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
3910 |
E3 |
Paper jam at start-up |
| TOSHIBA |
3910 |
E5 |
Paper jam in the paper tray |
| TOSHIBA |
3910 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
3910 |
C5 |
Copy
table end position error |
| TOSHIBA |
3910 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
3910 |
CE |
EPROM defective or missing |
| TOSHIBA |
3910 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
3910 |
CD |
EPROM end of life |
| TOSHIBA |
3910 |
CF |
Development unit missing, toner density problem |
| TOSHIBA |
4010 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
4010 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4010 |
E3 |
Paper jam at start-up |
| TOSHIBA |
4010 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
4010 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
4010 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
4010 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
4010 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
4010 |
ED |
Original jam in the feeder |
| TOSHIBA |
4010 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
4010 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
4010 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
4010 |
C5 |
Optical system initialization error |
| TOSHIBA |
4010 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4010 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
4010 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
4010 |
CF |
toner density error |
| TOSHIBA |
4010 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
4010 |
A2 |
Duplex functional problems |
| TOSHIBA |
4010 |
A4 |
Sorter problems |
| TOSHIBA |
4010 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
4010 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
4010 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
4010 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
4121 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
4121 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4121 |
E3 |
Paper jam at start-up |
| TOSHIBA |
4121 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
4121 |
E7 |
Paper jam at registration |
| TOSHIBA |
4121 |
C1 |
Copy
table reverse movement home position error in
sorter |
| TOSHIBA |
4121 |
C2 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
4121 |
C5 |
Copy
table end position error |
| TOSHIBA |
4121 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4121 |
C8 |
Lens
home position error |
| TOSHIBA |
4121 |
C9 |
5v
power supply defective |
| TOSHIBA |
4130 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
4130 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4130 |
E3 |
Paper jam at start-up |
| TOSHIBA |
4130 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
4130 |
E7 |
Paper jam at registration |
| TOSHIBA |
4130 |
C1 |
Copy
table reverse movement home position error in
sorter |
| TOSHIBA |
4130 |
C2 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
4130 |
C5 |
Copy
table end position error |
| TOSHIBA |
4130 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4130 |
C8 |
Lens
home position error |
| TOSHIBA |
4130 |
C9 |
5v
power supply defective |
| TOSHIBA |
4140 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
4140 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4140 |
E3 |
Paper jam at start-up |
| TOSHIBA |
4140 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
4140 |
E7 |
Paper jam at registration |
| TOSHIBA |
4140 |
C1 |
Copy
table reverse movement home position error in
sorter |
| TOSHIBA |
4140 |
C2 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
4140 |
C5 |
Copy
table end position error |
| TOSHIBA |
4140 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4140 |
C8 |
Lens
home position error |
| TOSHIBA |
4140 |
C9 |
5v
power supply defective |
| TOSHIBA |
4501 |
E0 |
Paper jammed in the machine at power-up |
| TOSHIBA |
4501 |
E1 |
Paper jam in the fusing or transport area |
| TOSHIBA |
4501 |
E2 |
Paper jam in the fusing unit |
| TOSHIBA |
4501 |
E3 |
Misfeed at the manual feed table |
| TOSHIBA |
4501 |
E6 |
Copy
table drive problem |
| TOSHIBA |
4501 |
E7 |
Copy
table drive problem |
| TOSHIBA |
4501 |
E8 |
Copy
table drive problem |
| TOSHIBA |
4501 |
E9 |
Copy
table reverse clutch not working |
| TOSHIBA |
4550 |
E1 |
Peper jam detected in machine |
| TOSHIBA |
4550 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4550 |
E3 |
Paper jam at start-up |
| TOSHIBA |
4550 |
E4 |
Pront cover open during copy cicle |
| TOSHIBA |
4550 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
4550 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
4550 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
4550 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
4550 |
ED |
Original jam in the feeder |
| TOSHIBA |
4550 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
4550 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
4550 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
4550 |
C5 |
Optical system initialization error |
| TOSHIBA |
4550 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4550 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
4550 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
4550 |
CF |
toner density error |
| TOSHIBA |
4550 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
4550 |
A2 |
Duplex functional problems |
| TOSHIBA |
4550 |
A4 |
Sorter problems |
| TOSHIBA |
4550 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
4550 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
4550 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
4550 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
4560 |
E01 |
Paper jam in the machine |
| TOSHIBA |
4560 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
4560 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
4560 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
4560 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
4560 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
4560 |
E11 |
Duplex entrance jam |
| TOSHIBA |
4560 |
E12 |
Paper misfeed at the manula feed table |
| TOSHIBA |
4560 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
4560 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
4560 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
4560 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
4560 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
4560 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
4560 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
4560 |
E22 |
Paper jam during transport |
| TOSHIBA |
4560 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
4560 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
4560 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
4560 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
4560 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
4560 |
E75 |
Original jammed |
| TOSHIBA |
4560 |
E81 |
Sorter paper jam |
| TOSHIBA |
4560 |
E82 |
Sorter paper jam |
| TOSHIBA |
4560 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
4560 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
4560 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
4560 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
4560 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
4560 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
4560 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
4560 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
4560 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
4560 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
4560 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
4560 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
4560 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
4560 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
4560 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
4560 |
C21 |
Optical system initialization error |
| TOSHIBA |
4560 |
C22 |
Lens
home position error |
| TOSHIBA |
4560 |
C23 |
mirrors home position error |
| TOSHIBA |
4560 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
4560 |
C33 |
Easy
set-up error |
| TOSHIBA |
4560 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
4560 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4560 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
4560 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
4560 |
C45 |
problems with the sub-thrmistor |
| TOSHIBA |
4560 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
4560 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
4560 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
4560 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
4560 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
4560 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
4560 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
4560 |
C80 |
Sorter power supply problems |
| TOSHIBA |
4560 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
4560 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
4560 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
4560 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
4560 |
C85 |
Home
position error in sorter |
| TOSHIBA |
4560 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
4560 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
4560 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
4560 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
4560 |
C94 |
Optical system initialization error |
| TOSHIBA |
4570 |
E01 |
Paper jam in the machine |
| TOSHIBA |
4570 |
E02 |
Paper jam in the fusing area |
| TOSHIBA |
4570 |
E03 |
Paer
jam at start-up |
| TOSHIBA |
4570 |
E04 |
Front cover open during the copy cycle |
| TOSHIBA |
4570 |
E05 |
Paper jam in the registration area |
| TOSHIBA |
4570 |
E08 |
Paper jam in the duplex unit |
| TOSHIBA |
4570 |
E11 |
Duplex entrance jam |
| TOSHIBA |
4570 |
E12 |
Paper misfeed at the manula feed table |
| TOSHIBA |
4570 |
E13 |
Paper jam at feed station 1 |
| TOSHIBA |
4570 |
E14 |
Paper jam at feed station 2 |
| TOSHIBA |
4570 |
E15 |
Paper jam at feed station 3 |
| TOSHIBA |
4570 |
E16 |
Paper jam at feed station 4 |
| TOSHIBA |
4570 |
E17 |
Paper jam at feed station 5 |
| TOSHIBA |
4570 |
E19 |
Paper feed jam at the large capacity tray |
| TOSHIBA |
4570 |
E21 |
Paper jam at the large capacity tray |
| TOSHIBA |
4570 |
E22 |
Paper jam during transport |
| TOSHIBA |
4570 |
E23 |
Paper jam in the registration area |
| TOSHIBA |
4570 |
E25 |
Paper jam in the fusing area |
| TOSHIBA |
4570 |
E71 |
Original jammed in the top feeder |
| TOSHIBA |
4570 |
E72 |
Original jammed during transport in the top
feeder |
| TOSHIBA |
4570 |
E73 |
Original jam at the feeder exit |
| TOSHIBA |
4570 |
E75 |
Original jammed |
| TOSHIBA |
4570 |
E81 |
Sorter paper jam |
| TOSHIBA |
4570 |
E82 |
Sorter paper jam |
| TOSHIBA |
4570 |
E83 |
Paper arrives at the sorter too early |
| TOSHIBA |
4570 |
E84 |
Paper jam in the sorter at start-up |
| TOSHIBA |
4570 |
E85 |
Sorter unit out of position during copy cycle |
| TOSHIBA |
4570 |
E88 |
Blocaj de hirtie in tavile sorterului |
| TOSHIBA |
4570 |
C01 |
Main
motor drive overloaded |
| TOSHIBA |
4570 |
C04 |
Optional paper feed unit motor problem |
| TOSHIBA |
4570 |
C05 |
Duplex main motor drive overload |
| TOSHIBA |
4570 |
C11 |
Duplex jogger motor drive overload |
| TOSHIBA |
4570 |
C12 |
Duplex exit motor overload |
| TOSHIBA |
4570 |
C13 |
Functional problems at first paper tray |
| TOSHIBA |
4570 |
C14 |
Functional problems at second paper tray |
| TOSHIBA |
4570 |
C15 |
Functional problems at third paper tray |
| TOSHIBA |
4570 |
C16 |
Functional problems at fourth paper tray |
| TOSHIBA |
4570 |
C17 |
Functional problems at fifth paper tray |
| TOSHIBA |
4570 |
C18 |
Functional problems at the large capacity paper
tray |
| TOSHIBA |
4570 |
C21 |
Optical system initialization error |
| TOSHIBA |
4570 |
C22 |
Lens
home position error |
| TOSHIBA |
4570 |
C23 |
mirrors home position error |
| TOSHIBA |
4570 |
C26 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
4570 |
C33 |
Easy
set-up error |
| TOSHIBA |
4570 |
C35 |
current leak at the transfer/separation unit |
| TOSHIBA |
4570 |
C41 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4570 |
C43 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
4570 |
C44 |
Abnormal temperature in the fuser, thermistor
error |
| TOSHIBA |
4570 |
C45 |
problems with the sub-thrmistor |
| TOSHIBA |
4570 |
C54 |
Communication with the sorter is intrerrupted |
| TOSHIBA |
4570 |
C55 |
Communication with the feeder is intrerrupted |
| TOSHIBA |
4570 |
C56 |
Communication problems with the optional paper
feed unit |
| TOSHIBA |
4570 |
C71 |
Top
Feeder motor overloaded |
| TOSHIBA |
4570 |
C72 |
Sensor problem in the feeder |
| TOSHIBA |
4570 |
C73 |
Feder EPROM initialization error |
| TOSHIBA |
4570 |
C74 |
Top
feeder exit sensor prblems |
| TOSHIBA |
4570 |
C80 |
Sorter power supply problems |
| TOSHIBA |
4570 |
C81 |
Sorter paper transport motor overloaded |
| TOSHIBA |
4570 |
C82 |
Sorter shift tray motor overloaded |
| TOSHIBA |
4570 |
C83 |
Upper position error in the sorter |
| TOSHIBA |
4570 |
C84 |
Lower limit position error in the sorter |
| TOSHIBA |
4570 |
C85 |
Home
position error in sorter |
| TOSHIBA |
4570 |
C86 |
Stapler positioning motor overload |
| TOSHIBA |
4570 |
C87 |
Stapler hammer motor overload |
| TOSHIBA |
4570 |
C88 |
Paper sensor error in sorter |
| TOSHIBA |
4570 |
C93 |
Top
feeder not receiving the stop signal |
| TOSHIBA |
4570 |
C94 |
Optical system initialization error |
| TOSHIBA |
4810 |
E1 |
Paper jam in the machine |
| TOSHIBA |
4810 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4810 |
E3 |
Paper jam detected at start-up |
| TOSHIBA |
4810 |
E5 |
Paper jam in the feed area |
| TOSHIBA |
4810 |
E7 |
Paper jam in the registration area |
| TOSHIBA |
4810 |
C1 |
Copy
table return home position error |
| TOSHIBA |
4810 |
C2 |
Paper start position not detected, copy table
switch defective |
| TOSHIBA |
4810 |
C5 |
Copy
table end position error |
| TOSHIBA |
4810 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4810 |
C8 |
Lens
home position error |
| TOSHIBA |
4810 |
C9 |
5v
power supply defective |
| TOSHIBA |
4810 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
4910 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
4910 |
E1 |
Paper jam in the machine |
| TOSHIBA |
4910 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
4910 |
E3 |
Paper jam at start-up |
| TOSHIBA |
4910 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
4910 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
4910 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
4910 |
C4 |
Paper feed cam drive problem |
| TOSHIBA |
4910 |
C5 |
Optic system initialization error |
| TOSHIBA |
4910 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
4910 |
C8 |
Scanner motor drive problems |
| TOSHIBA |
4910 |
CE |
EPROM defective or missing |
| TOSHIBA |
4910 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
4910 |
CD |
EPROM end of life |
| TOSHIBA |
4910 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
5010 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5010 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5010 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5010 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5010 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
5010 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
5010 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
5010 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
5010 |
ED |
Original jam in the feeder |
| TOSHIBA |
5010 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
5010 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
5010 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
5010 |
C5 |
Optical system initialization error |
| TOSHIBA |
5010 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5010 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
5010 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
5010 |
CF |
toner density error |
| TOSHIBA |
5010 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5010 |
A2 |
Duplex functional problems |
| TOSHIBA |
5010 |
A4 |
Sorter problems |
| TOSHIBA |
5010 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
5010 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
5010 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
5010 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
5010 |
A4 |
probleme cu sorterul |
| TOSHIBA |
5010 |
A5 |
probleme de comunicare intre procesor si
interfata sorterului |
| TOSHIBA |
5010 |
A6 |
Probleme de transmitere a semnalului la
interfata sorterului |
| TOSHIBA |
5010 |
A7 |
Probleme de comunicare cu alimentatorul |
| TOSHIBA |
5010 |
A9 |
lampa de expunere arsa, contacte imperfecte,
sursa principala |
| TOSHIBA |
5020 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5020 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5020 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5020 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5020 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
5020 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
5020 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
5020 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
5020 |
ED |
Original jam in the feeder |
| TOSHIBA |
5020 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
5020 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
5020 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
5020 |
C5 |
Optical system initialization error |
| TOSHIBA |
5020 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5020 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
5020 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
5020 |
CF |
toner density error |
| TOSHIBA |
5020 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5020 |
A2 |
Duplex functional problems |
| TOSHIBA |
5020 |
A4 |
Sorter problems |
| TOSHIBA |
5020 |
A5 |
Communication lost with the sorter |
| TOSHIBA |
5020 |
A6 |
Communication problems with the sorter interface |
| TOSHIBA |
5020 |
A7 |
Communication problems with the feeder |
| TOSHIBA |
5020 |
A9 |
Exposure lamp blown, or bad contacts |
| TOSHIBA |
5020 |
A4 |
probleme cu sorterul |
| TOSHIBA |
5020 |
A5 |
probleme de comunicare intre procesor si
interfata sorterului |
| TOSHIBA |
5020 |
A6 |
Probleme de transmitere a semnalului la
interfata sorterului |
| TOSHIBA |
5020 |
A7 |
Probleme de comunicare cu alimentatorul |
| TOSHIBA |
5020 |
A9 |
lampa de expunere arsa, contacte imperfecte,
sursa principala |
| TOSHIBA |
5110 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5110 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5110 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5110 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5110 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
5110 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
5110 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
5110 |
C0 |
Selector motor problems |
| TOSHIBA |
5110 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
5110 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
5110 |
C4 |
Paper feed cam motor drive problems |
| TOSHIBA |
5110 |
C5 |
Optic system initialization error |
| TOSHIBA |
5110 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5110 |
C8 |
Scanner motor drive problems |
| TOSHIBA |
5110 |
CE |
EPROM defective or missing |
| TOSHIBA |
5110 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5110 |
CD |
EPROM end of life |
| TOSHIBA |
5110 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
5120 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5120 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5120 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5120 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5120 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
5120 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
5120 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
5120 |
C0 |
Selector motor problems |
| TOSHIBA |
5120 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
5120 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
5120 |
C4 |
Paper feed cam motor drive problems |
| TOSHIBA |
5120 |
C5 |
Optic system initialization error |
| TOSHIBA |
5120 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5120 |
C8 |
Scanner motor drive problems |
| TOSHIBA |
5120 |
CE |
EPROM defective or missing |
| TOSHIBA |
5120 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5120 |
CD |
EPROM end of life |
| TOSHIBA |
5120 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
5511 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5511 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5511 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5511 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5511 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
5511 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
5511 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
5511 |
E7 |
Paper jam in the machine |
| TOSHIBA |
5511 |
C4 |
Paper feed cam motor drive problems |
| TOSHIBA |
5511 |
C5 |
Optic system initialization error |
| TOSHIBA |
5511 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5511 |
C8 |
Scanner motor drive problems |
| TOSHIBA |
5511 |
C9 |
Feeder jammed |
| TOSHIBA |
5511 |
CE |
EPROM defective or missing |
| TOSHIBA |
5511 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5511 |
CD |
EPROM end of life |
| TOSHIBA |
5511 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
5540 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5540 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5540 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5540 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5540 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
5540 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
5540 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
5540 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
5540 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
5540 |
ED |
Original jam in the feeder |
| TOSHIBA |
5540 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
5540 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
5540 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
5540 |
C5 |
Optical system initialization error |
| TOSHIBA |
5540 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5540 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
5540 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
5540 |
CE |
BC
RAM firmware problems |
| TOSHIBA |
5540 |
CF |
toner density error |
| TOSHIBA |
5540 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5540 |
A0 |
Abnormal signal received at the optional paper
feed tray |
| TOSHIBA |
5540 |
A1 |
Charge corona cleaner error |
| TOSHIBA |
5540 |
A2 |
Duplex functional problems |
| TOSHIBA |
5540 |
A3 |
Paper feed controller problems |
| TOSHIBA |
5540 |
A4 |
probleme cu sorterul |
| TOSHIBA |
5540 |
A5 |
probleme de comunicare intre procesor si
interfata sorterului |
| TOSHIBA |
5540 |
A6 |
Probleme de transmitere a semnalului la
interfata sorterului |
| TOSHIBA |
5540 |
A7 |
Probleme de comunicare cu alimentatorul |
| TOSHIBA |
5540 |
A9 |
lampa de expunere arsa, contacte imperfecte,
sursa principala |
| TOSHIBA |
5610 |
E0 |
Rezervorul de toner uzat e plin |
| TOSHIBA |
5610 |
E1 |
Blocaj de hirtie in aparat |
| TOSHIBA |
5610 |
E2 |
Blocaj de hirtie in zna cuptorului |
| TOSHIBA |
5610 |
E3 |
Blocaj de hirtie in aparat la pornire |
| TOSHIBA |
5610 |
E4 |
Capacul din fata deschis in timpul copierii |
| TOSHIBA |
5610 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
5610 |
E6 |
Blocaj de hirtie la alimentarea manuala |
| TOSHIBA |
5610 |
C0 |
Probleme cu motorul de selectare |
| TOSHIBA |
5610 |
C2 |
Probleme cu transmisia semnalului catre
sub-procesor |
| TOSHIBA |
5610 |
C3 |
Probleme cu transmisia semnalului catre
sub-procesor |
| TOSHIBA |
5610 |
C4 |
probleme la motorul camei de alimentare cu
hirtie |
| TOSHIBA |
5610 |
C5 |
sistemul optic nu se initializeaza |
| TOSHIBA |
5610 |
C7 |
cuptorul nu se incalzeste, probleme cu
termistorul, siguranta termica sau lampa din
cuptor |
| TOSHIBA |
5610 |
C8 |
motorul scanerului nu se opreste dupa ce timpul
alocat a trecut |
| TOSHIBA |
5610 |
CE |
EPROM-ul deconectat sau defect |
| TOSHIBA |
5610 |
CP |
motorul principal blocat |
| TOSHIBA |
5610 |
CD |
EPROM-ul a expirat, trebuie schimbat |
| TOSHIBA |
5610 |
CF |
unitatea de developare nu e montata, probleme cu
dozarea tonerului |
| TOSHIBA |
5620 |
E0 |
Rezervorul de toner uzat e plin |
| TOSHIBA |
5620 |
E1 |
Blocaj de hirtie in aparat |
| TOSHIBA |
5620 |
E2 |
Blocaj de hirtie in zna cuptorului |
| TOSHIBA |
5620 |
E3 |
Blocaj de hirtie in aparat la pornire |
| TOSHIBA |
5620 |
E4 |
Capacul din fata deschis in timpul copierii |
| TOSHIBA |
5620 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
5620 |
E6 |
Blocaj de hirtie la alimentarea manuala |
| TOSHIBA |
5620 |
C0 |
Probleme cu motorul de selectare |
| TOSHIBA |
5620 |
C2 |
Probleme cu transmisia semnalului catre
sub-procesor |
| TOSHIBA |
5620 |
C3 |
Probleme cu transmisia semnalului catre
sub-procesor |
| TOSHIBA |
5620 |
C4 |
probleme la motorul camei de alimentare cu
hirtie |
| TOSHIBA |
5620 |
C5 |
sistemul optic nu se initializeaza |
| TOSHIBA |
5620 |
C7 |
cuptorul nu se incalzeste, probleme cu
termistorul, siguranta termica sau lampa din
cuptor |
| TOSHIBA |
5620 |
C8 |
motorul scanerului nu se opreste dupa ce timpul
alocat a trecut |
| TOSHIBA |
5620 |
CE |
EPROM-ul deconectat sau defect |
| TOSHIBA |
5620 |
CP |
motorul principal blocat |
| TOSHIBA |
5620 |
CD |
EPROM-ul a expirat, trebuie schimbat |
| TOSHIBA |
5620 |
CF |
unitatea de developare nu e montata, probleme cu
dozarea tonerului |
| TOSHIBA |
5910 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
5910 |
E1 |
Paper jam in the machine |
| TOSHIBA |
5910 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
5910 |
E3 |
Paper jam at start-up |
| TOSHIBA |
5910 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
5910 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
5910 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
5910 |
E7 |
Paper jam in the machine |
| TOSHIBA |
5910 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
5910 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
5910 |
C4 |
Paper feed cam motor drive problems |
| TOSHIBA |
5910 |
C5 |
Optic system initialization error |
| TOSHIBA |
5910 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
5910 |
C8 |
Scanner motor drive problems |
| TOSHIBA |
5910 |
CE |
EPROM defective or missing |
| TOSHIBA |
5910 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
5910 |
CD |
EPROM end of life |
| TOSHIBA |
5910 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
7610 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
7610 |
E1 |
Paper jam in the machine |
| TOSHIBA |
7610 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
7610 |
E3 |
Paper jam at start-up |
| TOSHIBA |
7610 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
7610 |
E5 |
Blocaj de hirtie la caseta |
| TOSHIBA |
7610 |
E6 |
Paper jam at by-pass or defective sensor |
| TOSHIBA |
7610 |
E7 |
Paper jam in the machine |
| TOSHIBA |
7610 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
7610 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
7610 |
C4 |
Paper feed cam motor drive problems |
| TOSHIBA |
7610 |
C5 |
Optic system initialization error |
| TOSHIBA |
7610 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
7610 |
C8 |
Scanner motor drive problems |
| TOSHIBA |
7610 |
CE |
EPROM defective or missing |
| TOSHIBA |
7610 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
7610 |
CD |
EPROM end of life |
| TOSHIBA |
7610 |
CF |
Development unit not properly installed or
defective |
| TOSHIBA |
7720 |
E0 |
Used
toner collection bottle full |
| TOSHIBA |
7720 |
E1 |
Paper jam in the machine |
| TOSHIBA |
7720 |
E2 |
Paper jam in the fusing area |
| TOSHIBA |
7720 |
E3 |
Paper jam at start-up |
| TOSHIBA |
7720 |
E4 |
Front cover open during the copy cycle |
| TOSHIBA |
7720 |
E5 |
Paper feed jam in the paper tray |
| TOSHIBA |
7720 |
E8 |
Paper jam in the duplex unit |
| TOSHIBA |
7720 |
E9 |
Paper jam in the optional paper feed unit |
| TOSHIBA |
7720 |
EC |
Original misfeed in the feeder |
| TOSHIBA |
7720 |
ED |
Original jam in the feeder |
| TOSHIBA |
7720 |
EE |
Original jam at the feeder inverter or exit area |
| TOSHIBA |
7720 |
C2 |
processor to subprocessor communication problems |
| TOSHIBA |
7720 |
C3 |
processor to subprocessor communication problems |
| TOSHIBA |
7720 |
C5 |
Optical system initialization error |
| TOSHIBA |
7720 |
C7 |
Fusing unit warm-up error, defective thermistor,
fusing lamp or thermofuse |
| TOSHIBA |
7720 |
CB |
Original feed motor overloaded in the feeder |
| TOSHIBA |
7720 |
CC |
Original transport motor overloaded in the
feeder |
| TOSHIBA |
7720 |
CE |
BC
RAM firmware problems |
| TOSHIBA |
7720 |
CF |
toner density error |
| TOSHIBA |
7720 |
CP |
Main
motor drive overloaded |
| TOSHIBA |
7720 |
A0 |
Abnormal signal received at the optional paper
feed tray |
| TOSHIBA |
7720 |
A1 |
Charge corona cleaner error |
| TOSHIBA |
7720 |
A2 |
Duplex functional problems |
| TOSHIBA |
7720 |
A3 |
Paper feed controller problems |
| TOSHIBA |
7720 |
A4 |
probleme cu sorterul |
| TOSHIBA |
7720 |
A5 |
probleme de comunicare intre procesor si
interfata sorterului |
| TOSHIBA |
7720 |
A6 |
Probleme de transmitere a semnalului la
interfata sorterului |
| TOSHIBA |
7720 |
A7 |
Probleme de comunicare cu alimentatorul |
| TOSHIBA |
7720 |
A9 |
lampa de expunere arsa, contacte imperfecte,
sursa principala |
